I see no reason to catch the ejected round, it isn't going to break me. This includes grabbing a new magazine (loaded with subsonic ammo) from a belt pouch, removing the magazine currently in the weapon with retention, inserting the new magazine. Subsonic 556 is a complex solution to a simple problem.įirst of all: In an AR15, I can do a tactical reload and rack the bolt in seconds: single digit seconds. It is quick, quiet, accurate, easy to use and handy. 22 rimfire pistol in a holster is a MUCH better solution.
#Subsonic 223 loads powder manual#
Not to mention subsonic and full power rounds have vastly different impact points so the user has to remember which is which and apply to correct hold over.Įven if everything goes as planned, all this manual racking of the action takes time, is unweildy, noisy and a pain in the ass.Ī suppressed. IF there is a stuck bullet waiting in the bore, the next shot is going to be more than a surprise. Then you have to manually eject the fired case and rack the action to load a full power round. As suppressed subsonics are freakin quiet, in a time of stress it may be difficult to notice a squib round. You are then taking a chance by shooting a subsonic round through a potentially dirty barrel, which can cause the bullet to stick in the bore. To switch from one ammo to another you have to rack the action and eject the live round, which then has to be picked up. Quick, versitile, nothing extra to buy, nothing to convert. You put the original mag back in and you now have full powered ammo.
You switch mags (to a mag loaded with subsonic ammo) and fire that shot. You need want to fire A shot that absolutely has to be as quiet as possible. Use them at your own risk - your mileage may vary. Make sure you know what you're doing with reloading before trying these. I probably need to reduce it to 5.3 grains or so.Īll of these were shot in my Savage 10FP with 22" 1:9 barrel using a YHM 5.56 Phantom suppressor. I did some experimenting and found some other successful 223 loads, as follows: The load fizzled and I had a stuck bullet. I switched to CCI Benchrest primers - DON'T DO THIS. I tried this recipe using some Sierra 55 gr soft point boat tails and it worked fine. I called Hodgdon, and sure enough, they had some suggestions.
I don't want baffle strikes, nor stuck rounds.The Accurate S1250 subsonic 223 loads have been discussed before, but I had not seen many other recipes. I don't plan to shoot subsonic much out of my rifle, but when the ATF lets me have my stamp, the giggle-factor is too much to pass up. The problem is, they all keyholed at 100yd.Īside from normal case prep, how important is enlarging the flash holes? I noticed some significant blow-by of the powder on the cases would fireformed cases work better? My powder selection of Titegroup, does not even come close to taking up significant volume, but I'm using a hodgson published load is this article outdated information? I did not lubricate my bullets, but I've got an old tumbler and some moly powder aka Old_Painless' method would this help with consistency? And finally, for those who have done it, what effective range should I measure my loads? I shot all 20 rounds at 100yd and amusingly enough they "grouped" rather well I was able to get respectable groups once I got my elevation holdover down. I have some specific questions regarding development of these loads for suppressor use (I'm aiming for no keyholing). These fired pretty well, but chrono'd all over the place: 20 rounds: Av 1011fps, Spread 285, Min 828, Max 1113. 223 brass, FL sized CCI #400 small rifle primers 3.1gr Hodgson Titegroup (I also have trailboss and Clays available) Hornady 55gr FMJ (#2267) COAL: 2.200" Savage 12FV with 26" tube 223 loads using Hodgson Published load data. While eagerly awaiting my Specwar 7.62 to get out of jail, I took the time to create some subsonic.
0 kommentar(er)
